Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterChimney Cleaning in Burleson, TX
Chimney cleaning in Burleson typically runs $175-$325 for a standard sweep with NFPA 211 Level 2 camera inspection included, and most prefabricated fireplace systems we see need more than just a brush - they need chase cover and component inspection. We’re Level Two Chimney Co., and our crews serve Burleson from our Dallas-Fort Worth office with the Haven Standard in force on every job: written price before work starts, documented photo record on completion, and the 365-Day Done Right Promise. Call (682) 499-2712 to book or get your written estimate.
Why Burleson Homes Are Different
Burleson’s explosive growth from the 1980s through the 2000s built a city of prefabricated zero-clearance fireplaces inside wood-framed chases - not the masonry stacks most homeowners picture. These factory-built systems have sheet-metal chase covers, spark arrestors, and refractory panels that corrode and crack under North Texas heat cycles. Summer temperatures above 100°F accelerate expansion-and-contraction damage, while mild winters mean fireplaces sit idle, then see sudden heavy use during cold snaps like February 2021’s Winter Storm Uri. That start-stop pattern produces thick, sticky creosote from low-heat smoldering.
For the smaller stock of pre-1970s homes near downtown, the Blackland Prairie’s shrink-swell clay soils cause seasonal heaving that separates flashing and cracks mortar crowns - a soil-driven failure our crews probe for on every older masonry job.
Our Main Burleson Services
These are the three services Burleson homeowners call us about most often:
Chimney Cleaning & Sweep in Burleson
Our Chimney Cleaning & Sweep in Burleson service covers NFPA 211 Level 2 inspection with camera scan, creosote removal, and documented photo record. For prefab systems, we inspect chase covers, dampers, and refractory panels for heat-cycle damage that standard sweeps miss.
Chimney Repair in Burleson
Our Chimney Repair in Burleson work addresses chase cover replacement, crown sealing, flashing repair, and prefab component failure. We quote every repair in writing before starting, with photos showing exactly what failed and why.
Fireplace Services in Burleson
Our Fireplace Services in Burleson include gas log installation, refractory panel replacement, and damper repair for the factory-built systems common in local tract homes from the 1990s and 2000s.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterChimney Cap & Crown in Burleson
Most Burleson chimneys are prefabricated metal systems with chase covers that rust through after 15-25 years of North Texas heat cycling, plus a smaller stock of older masonry with mortar crowns cracked by Blackland Prairie soil heave. Chimney Cap & Crown work here means replacing corroded sheet-metal components on factory-built units and sealing or rebuilding masonry crowns before water enters the flue. Our crews carry Copperfield and Gelco caps sized for common prefab chase dimensions, and we document every condition with photos under Haven Standard Clause 4.
Chase Cover Replacement
Signs you need it
Rust stains on the chase siding, water dripping into the firebox during rain, or a cover that sounds hollow when tapped indicates metal fatigue from thermal expansion.
What it costs in Burleson
Chase cover replacement typically runs $450-$850 depending on chase dimensions and whether the spark arrestor is integrated.
How we do it
We measure the chase top, fabricate or order the replacement from Copperfield or Gelco stock, remove the rusted unit, seal the new cover with high-temp silicone, and photograph the install.
Crown Repair
Signs you need it
Hairline cracks in the mortar crown, crumbling edges, or interior water staining on masonry chimneys point to crown failure letting moisture into the flue.
What it costs in Burleson
Crown repair with elastomeric coating ranges $350-$650; full crown rebuild runs $800-$1,400 for severe deterioration.
How we do it
We grind out loose material, apply bonding agent, trowel new crown mix with proper overhang and drip edge, then seal with breathable waterproofing.
What Chimney Cap & Crown Costs in Burleson
| Item | Typical range in Burleson |
|---|---|
| Chase cover replacement | $450 - $850 |
| Crown repair with coating | $350 - $650 |
| Full crown rebuild | $800 - $1,400 |
How long does a chase cover last in Burleson?
Factory-built chase covers last 15-25 years in North Texas before rust-through; galvanized steel fails faster than stainless. We inspect cover condition during every sweep and show you photos so you can plan replacement before leaks start.
Can a cracked crown wait until next season?
A hairline crack can be coated if caught early, but water infiltration through a failed crown accelerates liner and masonry damage quickly in freeze-thaw cycles. We document the crack width and depth with photos, explain the timeline, and let you decide - no pressure, just evidence.
Chimney Liner & Rebuild in Burleson
Prefabricated fireplaces in Burleson’s 1980s-2000s tract homes have factory-built metal liners with finite lifespans, while older masonry near downtown may have unlined or clay-tile flues damaged by creosote corrosion or soil-shift stress. Chimney Liner & Rebuild work here means installing stainless steel liners in deteriorated systems or rebuilding sections where the Blackland Prairie’s clay soils have compromised structural integrity. We source DuraFlex and HeatShield materials through our Haven buying network, and every liner job includes camera verification and written warranty.
Stainless Steel Liner
Signs you need it
Flaking tile in the firebox, smoke drafting poorly into the room, or a Level 2 camera scan showing gaps or corrosion in the existing flue liner.
What it costs in Burleson
Stainless steel liner installation runs $2,200-$3,800 for a typical single-flue system, including insulation and top plate.
How we do it
We camera-scan the full flue length, measure diameter and height, drop the DuraFlex liner with insulation wrap, secure the top plate and bottom connection, and pressure-test the seal.
Partial Rebuild
Signs you need it
Spalling brick above the roofline, separated chimney from the house wall, or mortar joints washed out from soil-shift stress on pre-1980s masonry.
What it costs in Burleson
Partial rebuild of the upper chimney section typically runs $1,800-$3,500 depending on accessibility and brick matching.
How we do it
We scaffold the work area, remove damaged courses to sound masonry, install new brick and crown with proper flashing integration, and photograph each stage.
What Chimney Liner & Rebuild Costs in Burleson
| Item | Typical range in Burleson |
|---|---|
| Stainless steel liner | $2,200 - $3,800 |
| Partial rebuild | $1,800 - $3,500 |
| Liner replacement (flexible) | $1,800 - $3,200 |
Does a prefab fireplace need a new liner?
Factory-built units have listed metal liners that can’t be field-repaired; if corroded or separated, the entire firebox assembly often needs replacement. We camera-inspect to confirm factory liner condition and quote exact options.
How do I know if soil shift damaged my chimney?
Look for fresh gaps between chimney and siding, cracked interior drywall near the hearth, or tilting above the roofline. We check plumb and flashing integrity on every older Burleson job and show you what we find.
Brands We Service in Burleson
We stock and install caps, liners, and repair materials from DuraFlex, HeatShield, Gelco, and Copperfield - sourced through Haven’s buying network to keep pricing honest. Most common prefab chase cover sizes are available within 48 hours; custom fabrications typically arrive in 5-7 business days.
Pricing for Chimney Cleaning in Burleson, TX
| Service | Typical range in Burleson |
|---|---|
| Standard sweep with Level 2 inspection | $175 - $325 |
| Heavy creosote removal (Class III) | $325 - $495 |
| Chase cover replacement | $450 - $850 |
| Crown repair with coating | $350 - $650 |
| Full crown rebuild | $800 - $1,400 |
| Stainless steel liner | $2,200 - $3,800 |
| Flexible liner replacement | $1,800 - $3,200 |
| Partial chimney rebuild | $1,800 - $3,500 |
Prices move up in Burleson when chase covers are custom-sized for non-standard prefab units or when older masonry requires extensive brick matching. We deliver a written price, written scope, and written warranty before any work begins - Haven Standard Clause 1, no exceptions.
Neighborhoods We Serve in Burleson
Our crews work across Burleson with dispatch coordinated from our Dallas-Fort Worth office. Most appointments are available within 3-5 business days during peak pre-winter season.
- Mistletoe Hill
- Hidden Creek
- Plantation
- Bransom Ranch
- Old Town Burleson
Service Area - Cities Near Burleson
We serve homeowners throughout southern Tarrant and northern Johnson counties, including Mansfield, TX, Arlington, TX, Fort Worth, TX, and Haltom City, TX. Scheduling and dispatch run from our Dallas-Fort Worth office with local crews assigned by route.
Serving Burleson, TX - Our Local Coverage Area
We’re based in the Burleson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Burleson
Most chimney repairs and liner installations require a permit through the City of Burleson Building Inspections division; we handle permit submission as part of our scope and include the cost in your written estimate. Prefab component replacement typically does not trigger permitting.
We typically schedule 3-5 business days out during standard seasons and 7-10 days during pre-winter rushes in October and November. Live phone support answers 24/7 to book your slot.
Prefabricated units should still be swept and inspected annually per NFPA 211, but if the firebox, refractory panels, or factory liner show deterioration, replacement often costs less than repeated repairs. We camera-inspect and give you both options in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burleson Customers Say
"They ran a camera down the flue and showed me the cracked tiles on a screen. The previous company had swept it twice and never mentioned it."
- Gregory F."They told me the flue was fine and I did not need a liner. Charged me for the inspection and nothing else. That is why I have called them twice since."
- Hal M."We were buying the house and needed a real inspection. The report had photographs, the standard it was done to, and a clear repair figure. The seller paid for the repair."
- Lorna D.