Gelco Chimney Cleaning & Sweep Nationwide

Gelco Chimney Cleaning & Sweep in Fort Worth: What to Know First

We provide independent Gelco chimney cleaning and sweep services across Fort Worth, typically booking within three to five business days during sweep season and delivering a written price before any work starts. A standard Gelco system cleaning and Level 1 inspection runs $189-$275; Level 2 camera inspections with full photo documentation run $289-$395, depending on flue height and access. Every job carries our 365-Day Done Right Promise and leaves you with a documented photo record under Haven Standard Clause 4.

Call (682) 499-2712

This page is for Gelco product owners in Fort Worth neighborhoods like Fairmount, Ryan Place, and the Cultural District who need honest information about maintaining their chimney system. Whether you have a Gelco chimney cap, Gelco liner components, or Gelco termination hardware, we inspect and clean it without pushing unnecessary replacement. Call (682) 499-2712 for a free written estimate, or read on for the specifics.

How Gelco Products Fail - and How We Fix Them

• Gelco chimney cap mesh corrosion in Fort Worth’s clay soil zones. The 304 stainless mesh on Gelco standard-cap series holds up well inland, but we’ve tracked accelerated corrosion in homes near the Trinity River floodplain where soil salinity runs higher. The mesh pinholes, then creosote and moisture collect in the flue below. We replace with Gelco’s 316-grade upgrade or match with Famco equivalent when budget’s tight, and we document the soil exposure in your Clause 4 report.
• Gelco liner collar separation after freeze-thaw cycles. Fort Worth sees hard freezes every few winters, and the collar joints on Gelco’s earlier smooth-wall liner systems can gap where the termination meets the flue. We find this during camera inspection when smoke leaks into the chase cavity. Our fix: re-seat with HeatShield cerfractory foam sealant, or replace the collar assembly if the gap exceeds 3/16 inch. We show you the camera footage before quoting either path.
• Gelco top-sealing damper chain binding from creosote buildup. The cast-aluminum damper housings seal well when new, but the chain-and-spring mechanism gums up with Class II or III creosote, especially in Fort Worth homes burning unseasoned oak from local suppliers. The damper won’t fully open, and you get smoke backup. We disassemble, soak the chain in solvent, brush the housing, and test the seal with a smoke pencil. Replacement chains are Gelco OEM; we don’t substitute generic cable here.
• Gelco chimney pot mortar joint failure on historic conversions. The decorative pot series looks sharp on 1920s Fairmount bungalows, but the bedding mortar cracks when the pot shifts on a crown that’s already spalling. Water runs behind the pot, freezes, and pops the flue tile. We remove the pot, re-bed with CrownSeal or replace the crown entirely, then re-install with a proper cricket if the pitch demands it. The camera goes down before and after.
• Gelco multi-flue cap sizing errors from original mismeasurement. Big-box installers sometimes slap a Gelco multi-flue cap on without checking flue spacing, leaving one flue partially covered or the cap overhanging the crown edge. Rain hits the exposed flue; creosote washes down into the smoke chamber. We measure with a story pole, order the correct Gelco spec or fabricate a custom Copperfield cap through our Haven buying network, and write the exact dimensions into your warranty card.

Our Gelco Chimney Cleaning & Sweep Process

1. 1
   Schedule and confirm. You call (682) 499-2712, a live person answers, and we book a window. You get a text when your tech is en route with name and photo.
2. 2
   Arrive and protect. Our tech lays runners, inspects the appliance and chimney exterior, and sets up the camera rig. No work starts before you see the written price.
3. 3
   Camera-scan and document. We run the chimney camera the full flue length, recording liner condition, creosote class, and any Gelco-specific wear points. Clause 4 of the Haven Standard requires this photo record on every job.
4. 4
   Clean and service. Rotary brushing for creosote removal, soot vacuuming with HEPA filtration, and Gelco component inspection: cap mesh, damper operation, collar integrity. OEM parts if replacement is needed; aftermarket only if equivalent and approved.
5. 5
   Test and report. Smoke test, draft measurement, damper cycle check. We burn a small test fire if conditions allow. You receive the photo file, written scope, and written warranty before we pack up.
6. 6
   Follow-up. The 365-Day Done Right Promise is stamped on your paperwork. Call us if anything performs differently than documented; we come back.

Before

After

What Gelco Chimney Cleaning & Sweep Costs in Fort Worth

We don’t quote over the phone without seeing the system, but we do put the exact price in writing before any work begins. That’s Haven Standard Clause 1: have it in writing. Bring us a competitor’s written estimate and we’ll give you a free second opinion. Call (682) 499-2712 to schedule.

Why Fort Worth Homeowners Call Level Two Chimney Fort Worth for Gelco Work

We’ve cleaned and inspected more than 38,000 chimneys since 2009, and a solid slice of those have been Gelco systems in Fort Worth’s older neighborhoods where the brand’s been popular since the early 2000s. Corrine Halstead learned the trade in New York before running crews down here, and she’s particular about documentation: the camera doesn’t lie, and neither does the written estimate.

Our techs carry Gelco-compatible inventory from our Haven buying network, but we’re not locked to one supplier. When a Gelco part is back-ordered or overpriced, we source equivalent DuraFlex liner components or HeatShield refractory products and show you the comparison. Background-checked, uniformed, license number on the page. Live phone support 24/7. The 365-Day Done Right Promise applies to every job, no exceptions.

FAQs